Rayons > Guitares > Accessoires, pièces et outils > Pièces > Guitare - quincaillerie > Composants > Gibson > Potentiomètre - Arbre court/500k/Tone

Gibson Potentiomètre - Arbre court/500k/Tone

UGS: # 84458   |   Modèle: # AT510   |    Product Reviews4 Avis  Écrire une critique
Gibson
Gibson
Potentiomètre - Arbre court/500k/Tone
4 modèles à choisir:
Avisez-moi
    Écrivez votre adresse courriel.

Achetez en ligne
 Ajouter au panier

Achetez en succursale

Description
Q et R 1
Avis 4
AT300 :
Convient ; Gibson Les Pauls
Fonction ; volume
Valeur ; 300k ohms

AT310 :
Convient ; Gibson SG, ES-335, etc.
Fonction ; volume
Valeur ; 300k ohms, conicité linéaire

AT500 :
Convient ; Gibson Les Pauls
Fonction ; tonalité (ou volume, augmente légèrement la clarté de la sortie)
Valeur ; 500k ohms, taper

AT510 :
Convient ; Gibson SG, ES-335, etc.
Fonction ; tonalité
Valeur ; 500k ohms, taper

Poussez, tirez :
Valeur électrique : 500k Ohms, taper audio. Idéal pour la sélection de la bobine avec des micros Humbucking à 4 fils.

Q et R

Question: Do they have the gibson name stamped on them ?
- demandé le Dec 18, 2024
Répondre: Gibson is stamped on the bottom side.
- répondu par Robert Stayner
Cette réponse vous a-t-elle été utile ? Votez utile Voter n'est pas utile
  Veuillez vous connecter ou vous inscrire pour ajouter votre question

Avis

216.73.216.2
0
Mozilla/5.0 AppleWebKit/537.36 (KHTML, like Gecko; compatible; ClaudeBot/1.0; [email protected])
Poster le commentaire

It's a Pot..and it works.

2 personnes sur 3 ont trouvé cet avis pertinent

Caractéristiques  
Qualité  
Valeur  
Évaluation globale  
Relation au produit   I own it
Succursale   Brantford, Ontario
Pretty hard to do a review for something as basic as this. It does what it's supposed to do. After almost 50 years I needed to replace the volume controls in my 71 Les Paul Deluxe. The control cleaner and other methods just weren't helping any more. I ordered the 500 ohm long shaft as recommended for Les Paul models without taking apart my guitar first. When I did remove them for replacement, I found that the new pots with the long shaft were too long. I could have ordered the regular shaft length and it would have been fine. They make them that way to fit the contoured tops of the Les Paul and there is an adjustment that allows you to set the height of the volume control on the top of the guitar. 50 years ago, they were making the "pancake" bodies on LP models rather than the one piece bodies which they currently use. That might have something to do with it? Any way. does it fit....yeah with some finagling. Sound wise, it's right on! Exactly what I needed. Nice and smooth and with the same feel ( turning resistance) as what was in the guitar. If these last as well as the originals, I wont need to be replacing them in my lifetime...LOL.
Posted by Frank T on Feb 5, 2021
Est-ce que ce commentaire vous est utile? Vote helpful Vote not helpful Taguez ce commentaire

Also for Les Paul's and Volume

4 personnes sur 4 ont trouvé cet avis pertinent

Caractéristiques  
Qualité  
Valeur  
Évaluation globale  
Relation au produit   I own it
Succursale   Toronto (Bloor St.), Ontario
I used these pots for both volume and tone. They work smoothly without any issues. These were installed in my early 2000s Epi Les Paul. The description states that these are for Gibson SGs, ES-335s, etc., however, my LP uses short shaft pots. So check which one's you need before purchasing. The only issue was that the shaft diameter was larger than the holes in my guitar. I had to enlarge the holes slightly to make these fit. Shaft diameter is approximately 3/8? (9.5mm).
Posted by Dan on Oct 24, 2017
Est-ce que ce commentaire vous est utile? Vote helpful Vote not helpful Taguez ce commentaire

It's a push-pull pot

2 personnes sur 2 ont trouvé cet avis pertinent

Caractéristiques  
Qualité  
Valeur  
Évaluation globale  
Relation au produit   I own it
Succursale   Toronto (Bloor St.), Ontario
Currently, what is shown on the L&M site is not the correct image. If you go to the Gibson website it will show the correct image of this pot. However, contrary to the bad review of this pot, I found that it works well. It turns smoothly and the push-pull is not too stiff. I used this pot when I upgrade the pickups and electronics in my early 2000s Epi Les Paul. I coil split my new pickups and this pot does the job great. However, the shaft size was too large for the existing holes in my LP and I had to enlarge the holes slightly for the pot to fit. Shaft size is approximately 3/8? (9.5mm).
Posted by Dan on Oct 24, 2017
Est-ce que ce commentaire vous est utile? Vote helpful Vote not helpful Taguez ce commentaire

Push/pull potentiometre

7 personnes sur 10 ont trouvé cet avis pertinent

Caractéristiques  
Qualité  
Valeur  
Évaluation globale  
Relation au produit   I own it
Succursale   Laval, Quebec
Warning Alpha brand...the shaft is not gold as the picture...je trouve que le prix est trop haut pour cette qualité de slip coil even if it was a Gibson package...désapointée si j'avais su j'aurais preferee cts mais bon....this is a chinese part :(
Posted by Jose bellanger on Jan 14, 2016
Est-ce que ce commentaire vous est utile? Vote helpful Vote not helpful Taguez ce commentaire
Poster le commentaire

Complétez votre achat