Opens in a new window
HeadRush
FRFR-112 MKII Full Range/Flat Response 1x12 Powered Cabinet
Additional Photos:
PERFECT PARTNER FOR AMP MODELERS
If you're new to FRFR amplifiers FRFR stands for "full-range flat-response." This special type of amplification is very important for amp modeling pedals and pedalboards, as your amplifier needs to sound pure and transparent, so it can deliver a true "amp in the room" sound without coloring it as a traditional guitar amp would. The FRFR-112 MKII is precision-designed to get the most out of your modeler and deliver all the intricacies of your amp and cab emulations, with enough volume to be ready for any stage, rehearsal or jam session.
PURE AND POWERFUL TONE
FRFR-112 MKII outputs a massive 2500 watts, which means you have enough headroom for almost any performance or rehearsal. Featuring a specially voiced 12-inch woofer and high-frequency compression driver, the FRFR-112 MKII delivers a precise, full response across the entire frequency range, without any artificial colorationwhich is critical to getting the most out of your amp modeler. The FRFR-112 MKII's performance is exceptional, with max 131dB SPL and 46-22kHz frequency range.
ALL THE CONNECTIONS YOU NEED - INCLUDING BLUETOOTH®
FRFR-112 MKII features two combo XLR + 1/4" combo inputs for connecting your amp modeling pedal or pedalboard, each with their own independent volume controls. You can also wirelessly connect a mobile device to the FRFR-112 MKII via Bluetooth, so you can stream music wirelessly at rehearsal or during set breaks. There is also an XLR output for chaining more than one speaker together or sending the signal from your FRFR out to a front of house mix.
ADAPTS TO ANY STAGE OR ROOM
Stages and rehearsal rooms can easily become dense and mud-dy sounding as lower frequencies from different instruments battle each other; FRFR-112 MKII has a HPF cut switch to quickly pull those troublesome frequencies out and make sure your tone sits perfect in the mix. Unwanted electrical noise can also be a common problem; FRFR-112 MKII's ground lift switch can eliminate hums and buzzes resulting from ground loops.
ROAD-READY LIGHTWEIGHT DESIGN
FRFR-112 MKII is rugged yet relatively lightweight and easy to transport (at 35lbs / 15.8kg) making one trip load-ins at the gig or rehearsal space easier than ever. While you can use FRFR-112 MKII in its intended wedge position, its versatile design means that it can also be used in an upright or pole-mounted position, making it easier to direct your sound wherever you need it, which is especially helpful at outdoor gigs or other places where PA backline is limited.
POWERFUL, PROFESSIONAL SOUND
2500 watts of peak power ensures you have enough headroom for almost any live performance or rehearsal.
PRECISION-TUNED FOR AMP MODELERS
The cabinet design, 12" woofer, and HF compression driver are specially voiced for accurate, linear delivery of amplifier and cabinet emulations.
BLUETOOTH® ENABLED
Stream music wirelessly from your mobile device into FRFR-112 MKII's dedicated Bluetooth® channel.
ALL THE CONNECTIVITY YOU NEED
Two combo XLR + 1/4" inputs with independent volume controls and an XLR direct output allow for chaining speakers or sending to a front-of-house mix.
QUICKLY ADAPTS TO VENUES AND ROOMS
FRFR-112 MKII has a ground lift switch for eliminating noise issues caused by ground loops and a HPF EQ switch to help cut through muddy stage mixes.
LIGHTWEIGHT, FLEXIBLE AND STURDY
Weighing 35lbs / 15.8kg, FRFR-112 MKII is rugged yet easy to transport and can be used in a wedge, upright, or pole-mounted position.
Drivers: Low-Frequency: 12.0" (305 mm) driver, 2.5" (63 mm) high-temperature voice coil. / High-Frequency: 1.0" (25 mm) exit ceramic driver with 1.4" (35 mm) coil
Crossover Frequency: 2 kHz
Maximum SPL: 131 dB (peak) dB-SPL @ 1 m
Frequency Response: 53 Hz 20 kHz (+/-3 dB)
Frequency Range: 44 Hz 20 kHz (-10 dB)
Horn Coverage: 90° horizontal x 60° vertical (nominal)
Connectors: (2) XLR+1/4" (6.35 mm) TRS combo inputs (Balanced) / (1) XLR output (Link) / (1) IEC power cable input
Input Impedance: Line: 10 KΩ balanced, 20 KΩ unbalanced
Gain/Volume Control Range: 0 dB, +4 dBu nominal, +10 dBu for max output
HPF Switch: 100 Hz
Protection: Electronic clip, thermal, and transducer overdrive protection
Mounting/Installation: Standard 36 mm pole socket
Operating Temperature: 14°F to 113°F (-10°C to 45°C)
Dimensions (width x depth x height): 13.9" x 13.8" x 23.9" (351 mm x 354 mm x 607 mm)
Weight: 34.7 lbs. / 15.7 kg
Power
- Connection: IEC
- Input Voltage: 100-120V, 50/60 Hz; 220-240V, 50/60 Hz
- Consumption: 1100W
- Fuse: T15AL AC250V; 220-240V T6.3AL AC250V
If you're new to FRFR amplifiers FRFR stands for "full-range flat-response." This special type of amplification is very important for amp modeling pedals and pedalboards, as your amplifier needs to sound pure and transparent, so it can deliver a true "amp in the room" sound without coloring it as a traditional guitar amp would. The FRFR-112 MKII is precision-designed to get the most out of your modeler and deliver all the intricacies of your amp and cab emulations, with enough volume to be ready for any stage, rehearsal or jam session.
PURE AND POWERFUL TONE
FRFR-112 MKII outputs a massive 2500 watts, which means you have enough headroom for almost any performance or rehearsal. Featuring a specially voiced 12-inch woofer and high-frequency compression driver, the FRFR-112 MKII delivers a precise, full response across the entire frequency range, without any artificial colorationwhich is critical to getting the most out of your amp modeler. The FRFR-112 MKII's performance is exceptional, with max 131dB SPL and 46-22kHz frequency range.
ALL THE CONNECTIONS YOU NEED - INCLUDING BLUETOOTH®
FRFR-112 MKII features two combo XLR + 1/4" combo inputs for connecting your amp modeling pedal or pedalboard, each with their own independent volume controls. You can also wirelessly connect a mobile device to the FRFR-112 MKII via Bluetooth, so you can stream music wirelessly at rehearsal or during set breaks. There is also an XLR output for chaining more than one speaker together or sending the signal from your FRFR out to a front of house mix.
ADAPTS TO ANY STAGE OR ROOM
Stages and rehearsal rooms can easily become dense and mud-dy sounding as lower frequencies from different instruments battle each other; FRFR-112 MKII has a HPF cut switch to quickly pull those troublesome frequencies out and make sure your tone sits perfect in the mix. Unwanted electrical noise can also be a common problem; FRFR-112 MKII's ground lift switch can eliminate hums and buzzes resulting from ground loops.
ROAD-READY LIGHTWEIGHT DESIGN
FRFR-112 MKII is rugged yet relatively lightweight and easy to transport (at 35lbs / 15.8kg) making one trip load-ins at the gig or rehearsal space easier than ever. While you can use FRFR-112 MKII in its intended wedge position, its versatile design means that it can also be used in an upright or pole-mounted position, making it easier to direct your sound wherever you need it, which is especially helpful at outdoor gigs or other places where PA backline is limited.
POWERFUL, PROFESSIONAL SOUND
2500 watts of peak power ensures you have enough headroom for almost any live performance or rehearsal.
PRECISION-TUNED FOR AMP MODELERS
The cabinet design, 12" woofer, and HF compression driver are specially voiced for accurate, linear delivery of amplifier and cabinet emulations.
BLUETOOTH® ENABLED
Stream music wirelessly from your mobile device into FRFR-112 MKII's dedicated Bluetooth® channel.
ALL THE CONNECTIVITY YOU NEED
Two combo XLR + 1/4" inputs with independent volume controls and an XLR direct output allow for chaining speakers or sending to a front-of-house mix.
QUICKLY ADAPTS TO VENUES AND ROOMS
FRFR-112 MKII has a ground lift switch for eliminating noise issues caused by ground loops and a HPF EQ switch to help cut through muddy stage mixes.
LIGHTWEIGHT, FLEXIBLE AND STURDY
Weighing 35lbs / 15.8kg, FRFR-112 MKII is rugged yet easy to transport and can be used in a wedge, upright, or pole-mounted position.
Specifications
Output Power: 2500 WDrivers: Low-Frequency: 12.0" (305 mm) driver, 2.5" (63 mm) high-temperature voice coil. / High-Frequency: 1.0" (25 mm) exit ceramic driver with 1.4" (35 mm) coil
Crossover Frequency: 2 kHz
Maximum SPL: 131 dB (peak) dB-SPL @ 1 m
Frequency Response: 53 Hz 20 kHz (+/-3 dB)
Frequency Range: 44 Hz 20 kHz (-10 dB)
Horn Coverage: 90° horizontal x 60° vertical (nominal)
Connectors: (2) XLR+1/4" (6.35 mm) TRS combo inputs (Balanced) / (1) XLR output (Link) / (1) IEC power cable input
Input Impedance: Line: 10 KΩ balanced, 20 KΩ unbalanced
Gain/Volume Control Range: 0 dB, +4 dBu nominal, +10 dBu for max output
HPF Switch: 100 Hz
Protection: Electronic clip, thermal, and transducer overdrive protection
Mounting/Installation: Standard 36 mm pole socket
Operating Temperature: 14°F to 113°F (-10°C to 45°C)
Dimensions (width x depth x height): 13.9" x 13.8" x 23.9" (351 mm x 354 mm x 607 mm)
Weight: 34.7 lbs. / 15.7 kg
Power
- Connection: IEC
- Input Voltage: 100-120V, 50/60 Hz; 220-240V, 50/60 Hz
- Consumption: 1100W
- Fuse: T15AL AC250V; 220-240V T6.3AL AC250V
Q & A
Question: Firstly, I want an FRFR guitar monitor working in conjunction with a laptop (Logic Pro, Neural DSP plugins) and an interface. This would be a professional level guitar rig to replace the back-breaking tube amp I’ve been lugging around for years. Secondly, I’d also like to be able to use the same system as a mini PA system for small duo gigs with vocals, acoustic guitar, electric guitar, and possible backing tracks (bass, drums, keys, etc.), again using a laptop and interface at the front end. I was wondering if this Headrush unit would serve both these purposes well. I might consider getting 2 and running in stereo. Also, how much would poles cost if I wanted to mount them on stands?
- asked on Apr 7, 2024
- asked on Apr 7, 2024
Answer: Sure! That would work although I'm not sure how great it would sound? The cabinets are voiced for guitar not for PA purposes. Stands start at about $55, and any PA speaker stand would work.
- answered by Ron Elliott, Toronto (Bloor St.), Ontario
- answered by Ron Elliott, Toronto (Bloor St.), Ontario
Question: Is this speaker designed to work well with e-drums?
- asked on Apr 13, 2024
- asked on Apr 13, 2024
Answer: This one is designed for Guitars, although it may work fine for electronic drums as well.
- answered by Tanner Ling
- answered by Tanner Ling
Question: Would this sound good with bass tones as well? Is it more suited for electric guitar?
- asked on Apr 23, 2024
- asked on Apr 23, 2024
Answer: This is designed to work with floor processors with guitars.
It may work with a bass processor, but is not designed for those frequencies.
- answered by Bradford Pettigrew, Edmonton Highlands, Alberta
It may work with a bass processor, but is not designed for those frequencies.
- answered by Bradford Pettigrew, Edmonton Highlands, Alberta
Reviews
18.116.36.192
Mozilla/5.0 AppleWebKit/537.36 (KHTML, like Gecko; compatible; ClaudeBot/1.0; [email protected])
Headrush FRFR 0 of 0 customers found this review helpful
Features
Quality
Value
Overall
Product Experience I own it
Closest Store Fredericton, New Brunswick
Absolutely amazing. I’m running the HeadRush Pedal board and this thing sounds amazing. Amazing enough that I bought a second one. For modelling amps it’s a must. Staff was great as always.
Posted by Dave on Mar 16, 2024
Protect your investment with the Long & McQuade Performance Warranty
A warranty can be a very important factor when making a buying decision. Because repairs can be very expensive in terms of parts and labour costs, manufacturers usually only provide one year limited warranties that generally only cover items that malfunction due to a manufacturer’s defect. With an important purchase such as a musical
instrument or piece of studio gear, however, many people want to have the peace of mind in knowing that their investment will be protected should the product no longer be performing at 100%.
Because of this, Long & McQuade provides our customers with a FREE one-year Performance Warranty on most of our products. The Long & McQuade Performance Warranty supplements the manufacturer’s warranty to ensure that our customers receive complete “no hassle” warranty coverage within their first year.
How does the Long & McQuade Performance Warranty differ from most manufacturers' warranties?
- Performance Guarantee: Normal wear and tear is covered, so your product will be performing as well as the day you purchased it for the entire duration of the coverage. Band and Orchestral Performance Warranty does not include replacing pads or cleaning for woodwind instruments, unless deemed necessary by our repair staff. Ultrasonic cleaning for brass instruments will be provided if deemed necessary by our repair staff, but is not routinely offered under the Performance Warranty.
- Product Replacement: If your product cannot be fixed or costs too much to fix, we will replace it with the equivalent model for no additional charge. If this is not possible, a full refund will be provided.
- No Lemon Policy: Your product will be replaced should the same problem occur multiple times.
- Convenient: Easy drop off and pick up of the product at any Long & McQuade location.
- Guitar Setup: Guitars purchased at Long & McQuade come with 1 free setup, to be redeemed within 1 year for new guitars and 90 days for used guitars.
- Loaners Available: A loaner product may be given while the product is being repaired.
- Power Surge Protection: Your product is covered even if damaged from a power surge.
- Accessory Coverage: Any peripheral devices or accessories that come with your product (i.e. foot pedal, case) are also covered.
- Commercial Use Coverage: Music and recording professionals who purchase gear for “heavy-use” commercial purposes will still be covered.
Long & McQuade reserves the right to restrict the purchase of additional years of Performance Warranty. Used products come with a 3-month Long & McQuade Performance Warranty. Some products (i.e. computers, software, cymbals and other items) are covered only by the manufacturer‘s warranty. Consumables (i.e. strings, reeds, drum sticks, batteries, tubes, cross faders) are excluded as they are designed to be replaced. Cosmetic Damage, Accidental Damage, or problems caused by Humidity or Temperature Issues are not covered. Speakers damaged by overpowering are generally not covered. Our coverage does not provide compensation for loss of use. As of June 2018 the Performance Warranty is no longer transferable. The warranty is only valid in Canada.
Purchasing additional years of coverage
Some manufacturers provide warranties for longer than 1 year; however, these are usually limited warranties that do not provide the same coverage as the Long & McQuade Performance Warranty. Customers interested in more complete and convenient (but not necessarily longer) coverage are still able to purchase additional years of the Performance Warranty.
If you are interested in receiving this coverage for longer than one year, you have the option of purchasing additional years of the Performance Warranty. The pricing is as follows:
- NEW products: 4% of the current new selling price to double the warranty from 1 year to 2 years. 4% for each additional year.
- USED products: 4% of the current new selling price to increase the warranty from 3 months to 1 year. 4% for each additional year.
- GUITARS: 4% of the current new selling price to double the warranty from 1 year to 2 years. 4% for each additional year. $45 maximum. An additional free setup is not included with additional purchased years of Performance Warranty.
- BAND and ORCHESTRAL instruments: 4% of the current new selling price to double the warranty from 1 year to 2 years. 4% for each additional year.
Great Additions
Reserve in Store
| Product | SKU | Qty |
|---|---|---|
| FRFR-112 MKII Full Range/Flat Response 1x12 Powered Cabinet | 798122 |
